MikroTik RBwAPG-5HacD2HnD (wAP ac)
Dual-band (2.4GHz/5GHz) dual-radio 802.11a/b/g/n/ac wireless access point with integrated antenna and two gigabit Ethernet ports, one supporting PoE-in, in a weatherproof enclosure. The SoC contains a powerful quad-core ARM CPU with hardware-accelerated encryption support.
The commercial name of the access point is wAP ac. Do not confuse this ipq40xx-based model with the older ath79-based RBwAPG-5HacT2HnD, also marketed as wAP ac.
Supported Versions
Hardware highlights
Installation
→ Install OpenWrt on MikroTik devices
→ Install OpenWrt (generic instructions)
Installation is as on other MikroTik devices. In summary, permanent installation occurs in two steps:
- Boot an initramfs image over TFTP.
- Flash the final image using
sysupgrade.
The RouterOS 7 bootloader is not compatible with OpenWrt. If a device is running the RouterOS 7 bootloader, downgrade it to RouterOS 6 and flash the bootloader before installing OpenWrt.
Basic configuration
After flashing, proceed with basic configuration to set up the Internet connection, configure wireless, etc.
Specific configuration
Network interfaces
The default network configuration:
| Interface Name | Case Label | Description | Default configuration |
|---|---|---|---|
br-lan | LAN | 192.168.1.1/24 | |
eth0 | CPU GMAC, connected to switch | None | |
sw-eth1 | ETH1 | Switch port, accepts PoE In | Bridged to br-lan |
sw-eth2 | ETH2 | Switch port | Bridged to br-lan |
phy0-ap0 | WiFi, 2.4GHz 802.11b/g/n | Disabled; bridged to br-lan |
|
phy1-ap0 | WiFi, 5GHz 802.11a/n/ac | Disabled; bridged to br-lan |
Buttons
| Button Name | Case Label | Event |
|---|---|---|
| Reset | RESET | reset |
LEDs
| LED Name | Case Label | Color | Internal name | Use |
|---|---|---|---|---|
| Power | PWR | blue:power | Blue | Keep state from bootloader (expected on when powered) |
| User | USR | green:user | Green | Diag indicator: blink patterns for boot, failsafe, and upgrade states; solid in running state |
ETH1 and ETH2 also have one green and one amber LED each, but they are configured to remain under switch control to show link/activity (green) and speed (amber), and are not under OpenWrt’s control.
→ Generic LED configuration documentation.
Hardware
Info
| Architecture | ARMv7 (32-bit) |
|---|---|
| Vendor | Qualcomm |
| Bootloader | RouterBoot |
| System-On-Chip | Qualcomm IPQ4018 |
| CPU/Speed | Qualcomm IPQ4018 (SoC integrated), 4x 716 MHz |
| CPU Implementation | Cortex-A7 with NEON and VPFv4 |
| Flash-Chip | Winbond W25Q128JVSM |
| Flash size | 16 MiB |
| RAM | 128 MiB |
| Wireless | Qualcomm IPQ4018 (SoC integrated), 2.4GHz 802.11b/g/n, 5GHz 802.11a/n/ac |
| Wi-Fi Generation | 2.4GHz → WiFi 4, 5GHz → Wi-Fi 5 |
| Ethernet | 2x 10/100/1000 Mbit/s, VLAN support |
| Switch | Qualcomm Atheros QCA8072 |
| USB | No |
| Serial | Yes, via pads on board |
| Powering | DC jack 10–57V, PoE-in 802.3af/at or 10–57V |
| Ingress Protection | IP54 |
Flash Layout
| MikroTik RBwAPG-5HacD2HnD (wAP ac) Flash Layout | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Layer0 | raw NOR flash memory chip (spi0.0: w25q128jv) 16384 KiB | |||||||||
| Layer1 | mtd0 Qualcomm 512 KiB | mtd1 RouterBoot 512 KiB | mtd5 firmware 15360 KiB |
|||||||
| Layer2 | 56 KiB | mtd2 hard_config 8 KiB | mtd3 dtb_config ~32 KiB | ~148 KiB | mtd4 soft_config 4 KiB | 264 KiB | mtd6 kernel | mtd7 rootfs |
||
| mountpoint | / |
|||||||||
| filesystem | OverlayFS | |||||||||
| Layer3 | mtd8 rootfs_data |
|||||||||
| mountpoint | /rom | /overlay |
||||||||
| filesystem | SquashFS | JFFS2 | ||||||||
Photos
Opening the case
Loosen screws.
Serial
→ port.serial: General information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device (same as mikrotik hap ac2):
By default, the serial port is disabled during boot. To enable it, “no UART” needs to be disabled in hard_config.
| Serial connection parameters for MikroTik wAP ac | 11520, 8N1 |
|---|
Bootlogs
OEM bootlog
Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096 S - IMAGE_VARIANT_STRING=DAABANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000021 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 1678 - bootable_media_detect_success, Start B - 1692 - elf_loader_entry, Start B - 5069 - auth_hash_seg_entry, Start B - 7213 - auth_hash_seg_exit, Start B - 572130 - elf_segs_hash_verify_entry, Start B - 687491 - PBL, End B - 687516 - SBL1, Start B - 775874 - pm_device_init, Start D - 6 - pm_device_init, Delta B - 777386 - boot_flash_init, Start D - 46150 - boot_flash_init, Delta B - 827727 - boot_config_data_table_init, Start D - 3838 - boot_config_data_table_init, Delta - (419 Bytes) B - 834944 - clock_init, Start D - 7567 - clock_init, Delta B - 847033 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0 B - 850523 - sbl1_ddr_set_params, Start B - 855510 - cpr_init, Start D - 2 - cpr_init, Delta B - 860003 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13149 - sbl1_ddr_set_params, Delta B - 873704 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 944853 - sbl1_wait_for_ddr_training, Start D - 30 - sbl1_wait_for_ddr_training, Delta B - 960473 - Image Load, Start D - 143597 - QSEE Image Loaded, Delta - (267732 Bytes) B - 1104570 - Image Load, Start D - 1446 - SEC Image Loaded, Delta - (2048 Bytes) B - 1114983 - Image Load, Start D - 16275 - APPSBL Image Loaded, Delta - (28636 Bytes) B - 1131677 - QSEE Execution, Start D - 58 - QSEE Execution, Delta B - 1137778 - SBL1, End D - 452374 - SBL1, Delta S - Flash Throughput, 1854 KB/s (298835 Bytes, 161137 us) S - DDR Frequency, 537 MHz RouterBOOT backup booter 6.44.5 RBwAPG-5HacD2HnD CPU frequency: 716 MHz Memory size: 128 MiB Storage size: 16 MiB Press any key within 2 seconds to enter setup.. loading kernel... OK setting up elf image... OK jumping to kernel code Starting... Starting services...
OpenWrt bootlog
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.15.74 (user@host) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.3.0 r21015-802bfe080678) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Oct 20 02:39:57 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: MikroTik wAP ac [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] HighMem [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x0000000087ffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s16332 r8192 d20532 u45056 [ 0.000000] pcpu-alloc: s16332 r8192 d20532 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32484 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 116404K/131072K available (6597K kernel code, 608K rwdata, 1672K rodata, 1024K init, 240K bss, 14668K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000025] Switching to timer-based delay loop, resolution 20ns [ 0.000333] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000365] pid_max: default: 32768 minimum: 301 [ 0.000624] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000659] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001826] CPU: Testing write buffer coherency: ok [ 0.002262] qcom_scm: convention: smc legacy [ 0.003493] Setting up static identity map for 0x80300000 - 0x8030003c [ 0.003683] rcu: Hierarchical SRCU implementation. [ 0.003962] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.004353] smp: Bringing up secondary CPUs ... [ 0.008064] smp: Brought up 1 node, 4 CPUs [ 0.008108] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.008124] CPU: All CPU(s) started in SVC mode. [ 0.012884] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.013067] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013106] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.013430] pinctrl core: initialized pinctrl subsystem [ 0.015235] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.015751] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.016896] thermal_sys: Registered thermal governor 'step_wise' [ 0.017409] cpuidle: using governor ladder [ 0.017475] cpuidle: using governor menu [ 0.042111] cryptd: max_cpu_qlen set to 1000 [ 0.046597] usbcore: registered new interface driver usbfs [ 0.046684] usbcore: registered new interface driver hub [ 0.046749] usbcore: registered new device driver usb [ 0.046805] pps_core: LinuxPPS API ver. 1 registered [ 0.046819] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.046852] PTP clock support registered [ 0.048962] clocksource: Switched to clocksource arch_sys_counter [ 0.049903] NET: Registered PF_INET protocol family [ 0.050243] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.050896] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.050954] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.050979] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051011] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.051049] TCP: Hash tables configured (established 1024 bind 1024) [ 0.051194] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.051253] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.051561] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.051614] PCI: CLS 0 bytes, default 64 [ 0.054162] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.059199] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.059235] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.192284] bounce: pool size: 64 pages [ 0.195294] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.195334] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.196045] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.196157] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.196251] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.196568] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.197202] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.197258] msm_serial 78af000.serial: uartclk = 1843200 [ 0.197314] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 33, base_baud = 115200) is a MSM [ 0.197355] msm_serial: console setup on port #0 [ 0.736364] printk: console [ttyMSM0] enabled [ 0.741499] msm_serial: driver initialized [ 0.751131] loop: module loaded [ 0.752324] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.754740] spi-nor spi0.0: w25q128jv (16384 Kbytes) [ 0.760497] 3 fixed-partitions partitions found on MTD device spi0.0 [ 0.765369] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 0.771725] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 0.778281] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 0.784572] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 0.791266] Creating 3 MTD partitions on "spi0.0": [ 0.797543] 0x000000000000-0x000000080000 : "Qualcomm" [ 0.802960] 0x000000080000-0x000000100000 : "RouterBoot" [ 0.812991] 3 routerbootpart partitions found on MTD device RouterBoot [ 0.813040] Creating 3 MTD partitions on "RouterBoot": [ 0.819282] 0x00000000e000-0x000000010000 : "hard_config" [ 0.824947] 0x000000010000-0x000000017c6e : "dtb_config" [ 0.830404] 0x00000003d000-0x00000003e000 : "soft_config" [ 0.835730] 0x000000100000-0x000001000000 : "firmware" [ 0.845497] 2 minor-fw partitions found on MTD device firmware [ 0.845548] Creating 2 MTD partitions on "firmware": [ 0.851424] 0x000000000000-0x000000330000 : "kernel" [ 0.857029] 0x000000330000-0x000000f00000 : "rootfs" [ 0.861908] mtd: device 7 (rootfs) set to be root filesystem [ 0.866582] 1 squashfs-split partitions found on MTD device rootfs [ 0.872069] 0x0000009a0000-0x000000f00000 : "rootfs_data" [ 0.906109] ipqess-edma c080000.ethernet: generated random MAC address xx:xx:xx:xx:xx:xx [ 0.930754] i2c_dev: i2c /dev entries driver [ 0.932717] sdhci: Secure Digital Host Controller Interface driver [ 0.934113] sdhci: Copyright(c) Pierre Ossman [ 0.940179] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.950016] MikroTik RouterBOARD hardware configuration sysfs driver v0.07 [ 0.951419] MikroTik RouterBOARD software configuration sysfs driver v0.05 [ 0.957940] NET: Registered PF_INET6 protocol family [ 0.966092] Segment Routing with IPv6 [ 0.969079] In-situ OAM (IOAM) with IPv6 [ 0.972619] NET: Registered PF_PACKET protocol family [ 0.976830] 8021q: 802.1Q VLAN Support v1.8 [ 0.981498] Registering SWP/SWPB emulation handler [ 0.999672] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode [ 0.999976] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx [ 1.083543] qca8k-ipq4019 c000000.switch sw-eth2 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8072] (irq=POLL) [ 1.175517] qca8k-ipq4019 c000000.switch sw-eth1 (uninitialized): PHY [90000.mdio-1:04] driver [Qualcomm QCA8072] (irq=POLL) [ 1.186438] DSA: tree 0 setup [ 1.199400] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 1.201493] Freeing unused kernel image (initmem) memory: 1024K [ 1.229798] Run /sbin/init as init process [ 1.229881] with arguments: [ 1.229900] /sbin/init [ 1.229923] with environment: [ 1.229940] HOME=/ [ 1.229960] TERM=linux [ 1.895793] init: Console is alive [ 1.896174] init: - watchdog - [ 3.158098] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.314424] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.316428] init: - preinit - [ 4.667048] random: jshn: uninitialized urandom read (4 bytes read) [ 4.719425] random: jshn: uninitialized urandom read (4 bytes read) [ 4.757072] random: jshn: uninitialized urandom read (4 bytes read) [ 5.042686] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 5.043735] device eth0 entered promiscuous mode [ 5.049617] qca8k-ipq4019 c000000.switch sw-eth1: configuring for phy/psgmii link mode [ 5.054823] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 5.707627] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.730378] random: procd: uninitialized urandom read (4 bytes read) [ 7.771370] qca8k-ipq4019 c000000.switch sw-eth1: Link is Up - 1Gbps/Full - flow control off [ 7.771980] IPv6: ADDRCONF(NETDEV_CHANGE): sw-eth1: link becomes ready [ 8.089417] jffs2: notice: (234) jffs2_build_xattr_subsystem: complete building xattr subsystem, 10 of xdatum (8 unchecked, 1 orphan) and 12 of xref (1 dead, 0 orphan) found. [ 8.096830] mount_root: switching to jffs2 overlay [ 8.159058] random: crng init done [ 8.159133] random: 6 urandom warning(s) missed due to ratelimiting [ 8.163542] overlayfs: upper fs does not support tmpfile. [ 8.209898] urandom-seed: Seeding with /etc/urandom.seed [ 8.461852] qca8k-ipq4019 c000000.switch sw-eth1: Link is Down [ 8.462228] device eth0 left promiscuous mode [ 8.475358] procd: - early - [ 8.475646] procd: - watchdog - [ 9.134410] procd: - watchdog - [ 9.155277] procd: - ubus - [ 9.287493] procd: - init - [ 10.370124] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.472457] urngd: v1.0.2 started. [ 10.496576] cryptodev: driver 1.12 loaded. [ 10.501246] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064 [ 10.501305] Backport generated by backports.git v5.15.58-1-0-g42a95ce7 [ 10.600027] PPP generic driver version 2.4.2 [ 10.601544] NET: Registered PF_PPPOX protocol family [ 12.226843] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 12.226929] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 12.238922] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 12.290530] ath10k_ahb a000000.wifi: Loading BDF type 0 [ 12.529552] ath10k_ahb a000000.wifi: board_file api 1 bmi_id 0:16 crc32 4b1f5e2b [ 13.817619] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 13.817738] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 13.853994] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 13.854970] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 13.989114] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 14.106990] ath: EEPROM regdomain: 0x0 [ 14.107184] ath: EEPROM indicates default country code should be used [ 14.107274] ath: doing EEPROM country->regdmn map search [ 14.107390] ath: country maps to regdmn code: 0x3a [ 14.107500] ath: Country alpha2 being used: US [ 14.107598] ath: Regpair used: 0x3a [ 15.786022] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 15.786105] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 15.807053] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 15.853477] ath10k_ahb a800000.wifi: Loading BDF type 0 [ 16.085612] ath10k_ahb a800000.wifi: board_file api 1 bmi_id 0:17 crc32 a9d8e46d [ 17.374011] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 17.374128] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 17.410055] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 17.411047] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 17.536012] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 17.649777] ath: EEPROM regdomain: 0x0 [ 17.649973] ath: EEPROM indicates default country code should be used [ 17.650066] ath: doing EEPROM country->regdmn map search [ 17.650184] ath: country maps to regdmn code: 0x3a [ 17.650296] ath: Country alpha2 being used: US [ 17.650393] ath: Regpair used: 0x3a [ 17.695782] kmodloader: done loading kernel modules from /etc/modules.d/* [ 26.261318] ipqess-edma c080000.ethernet eth0: Link is Down [ 26.268203] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode [ 26.268610] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 26.275323] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 26.284288] device eth0 entered promiscuous mode [ 26.289791] qca8k-ipq4019 c000000.switch sw-eth1: configuring for phy/psgmii link mode [ 26.296125] br-lan: port 1(sw-eth1) entered blocking state [ 26.302360] br-lan: port 1(sw-eth1) entered disabled state [ 26.308455] device sw-eth1 entered promiscuous mode [ 26.336506] qca8k-ipq4019 c000000.switch sw-eth2: configuring for phy/psgmii link mode [ 26.339081] br-lan: port 2(sw-eth2) entered blocking state [ 26.343379] br-lan: port 2(sw-eth2) entered disabled state [ 26.349333] device sw-eth2 entered promiscuous mode [ 28.411020] qca8k-ipq4019 c000000.switch sw-eth1: Link is Up - 1Gbps/Full - flow control off [ 29.285219] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 29.285319] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 29.320827] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 29.321776] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 29.622367] ath10k_ahb a000000.wifi: rts threshold -1 [ 29.624185] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 29.627254] br-lan: port 1(sw-eth1) entered blocking state [ 29.637599] br-lan: port 1(sw-eth1) entered forwarding state [ 29.644497] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 29.648853] br-lan: port 3(phy0-ap0) entered blocking state [ 29.654327] br-lan: port 3(phy0-ap0) entered disabled state [ 29.660329] device phy0-ap0 entered promiscuous mode [ 29.802771] ath10k_ahb a000000.wifi: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 30.022499] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready [ 30.023018] br-lan: port 3(phy0-ap0) entered blocking state [ 30.028013] br-lan: port 3(phy0-ap0) entered forwarding state [ 31.817282] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 31.817366] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 31.853275] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 31.854647] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 32.138176] ath10k_ahb a800000.wifi: rts threshold -1 [ 32.138634] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 32.152285] br-lan: port 4(phy1-ap0) entered blocking state [ 32.153284] br-lan: port 4(phy1-ap0) entered disabled state [ 32.159680] device phy1-ap0 entered promiscuous mode [ 32.840307] IPv6: ADDRCONF(NETDEV_CHANGE): phy1-ap0: link becomes ready [ 32.842564] br-lan: port 4(phy1-ap0) entered blocking state [ 32.846130] br-lan: port 4(phy1-ap0) entered forwarding state